Home > Fasteners > Screws > Self Drilling Screw > Hex Head Tek Screw With Washer, Coated

Enlarge

Hex Head Tek Screw With Washer, Coated

Hex head self drilling screws are fasteners that have a drill point which enables users to drill them directly into material without having to pre-drill a hole. The EPDM washer under the head provides a consistent weather-tight seal. In addition to the standard tek points, certain sizes are available in a #1 stitch point for lap joints on metal roofing, or a #5 point for thicker material up to 1/2" thick. These fasteners are available with a long life coating, and in conjunction with the bonded sealing washer these screws are commonly used for metal roofing installation.

Products
Drill Point Specifications
Head Dimensions
Washer Dimensions

Drill Point Specifications

#2 & #3 Standard Drill Point Self Drilling Screws

#2 & #3 Standard Drill Point for Self Drilling Screws dimensions

SAE J78-2013
Nominal Size or Basic Screw Diameter		Threads per Inch	T		t		P		Minimum Practical Nominal Screw Lengths, Formed Points				Minimum Torsional Strength, lb - in (STEEL SCREWS ONLY)
			Major Diameter		Minor Diameter		Protrusion Allowance		Minimum Practical Nominal Screw Lengths, Formed Points
			Max	Min	Max	Min	#2 Point	#3 Point	90° Head, #2 Point	Csk Head, #2 Point	90° Head, #3 Point	Csk Head, #3 Point
#4	0.112	24	0.114	0.110	0.086	0.082	0.163	-	5/16	3/8	-	-	14
#6	0.138	20	0.139	0.135	0.104	0.099	0.190	0.220	5/16	3/8	3/8	7/16	24
#8	0.164	18	0.166	0.161	0.122	0.116	0.211	0.251	3/8	7/16	7/16	1/2	42
#10	0.190	16	0.189	0.183	0.141	0.135	0.235	0.300	7/16	1/2	1/2	9/16	61
#12	0.216	14	0.215	0.209	0.164	0.157	0.283	0.353	1/2	5/8	1/2	5/8	92
#14	0.250	14	0.246	0.240	0.192	0.185	0.318	0.393	1/2	5/8	1/2	5/8	150

All dimensions are in inches.

	Steel	Stainless
Material	AISI 1016 - 1024 or equivalent steel	410 or 18-8 stainless steel
Heat Treatment	Screws shall be quenched in liquid and then tempered by reheating to 625°F minimum.	410 stainless steel screws shall be hardened and tempered by heating to 1800°-1900°F sufficient for austenitization, held for at least 1/2 hour and rapid air or oil-quenched then reheating to 500°-600°F for at least 1 hour and air cooled to provide the specified hardness.
Case Hardness	Rockwell C52 - 58	410 SS: Rockwell C55 minimum
Case Depth	No. 4 & 6 diameter: .002 - .007 No. 8 thru 12 diameter: .004 - .009 1/4 diameter & larger: .005 - .011	-
Core Hardness	Rockwell C32 - 40 (after tempering)	410 SS: Rockwell C38 - 42 (after tempering) 18-8 SS: Rockwell B90 - C25 (approx.)

#4 & #5 Drill Point Self Drilling Screws for Thicker Materials

Diameter & Thread Pitch	Point Size	T		t		A		B		Drilling Capacity		Performance Info (STEEL SCREWS ONLY)
		Major Thread Diameter		Minor Thread Diameter		Drill Point Length		Drill Point Diameter		Drilling Capacity		Steel Gauge	Shear Strength (lapped steel) (lbs)	Pullout Strength (lbs)
		Max	Min	Max	Min	Max	Min	Max	Min	Max	Min	Steel Gauge	Shear Strength (lapped steel) (lbs)	Pullout Strength (lbs)
10-24	#5	0.189	0.181	0.162	0.158	0.413	0.373	0.173	0.165	0.250	0.125	-	-	-
12-24	#4	0.216	0.207	0.172	0.168	0.523	0.495	0.202	0.190	0.312	0.145	12	2000	1500
12-24	#5	0.216	0.207	0.172	0.168	0.640	0.603	0.202	0.190	0.500	0.250	1/8	2700	2200
12-24	#5	0.216	0.207	0.172	0.168	0.640	0.603	0.202	0.190	0.500	0.250	1/4	2760	4000
1/4-20	#4	0.246	0.239	0.192	0.185	0.511	0.471	0.227	0.215	0.312	0.145	12	1800	-
1/4-20	#5	0.249	0.242	0.192	0.185	0.629	0.569	0.227	0.222	0.500	0.250	12	1800	-

All dimensions are in inches.

	Steel	Stainless
Material	AISI 1022 or equivalent steel	410 stainless steel
Heat Treatment	Screws shall be quenched in liquid and then tempered by reheating to 625°F minimum.	410 stainless steel screws shall be hardened and tempered by heating to 1800°-1900°F sufficient for austenitization, held for at least 1/2 hour and rapid air or oil-quenched then reheating to 500°-600°F for at least 1 hour and air cooled to provide the specified hardness.
Case Hardness	Rockwell C52 - 58	410 SS: Rockwell C55 minimum
Case Depth	No. 10 & 12 diameter: .004 - .009 1/4 diameter & larger: .005 - .011	-
Core Hardness	Rockwell C21 - 43 (after tempering)	Rockwell C38 - 42 (after tempering)
Shear Strength	The average ultimate values for shear strength are listed in the above table. Safety factors should be used when designing final applications.	-
Pullout Strength	The average ultimate values for pullout strength are listed in the above table. Safety factors should be used when designing final applications.	-

#1 Drill Point Self Drilling Stitch Screws

#1 Drill Point for Self Drilling Stitch Screws dimensions

Nominal Diameter	Threads per Inch	W		P
		Drill Point Width		Length of Drill Point
		Max	Min	Max	Min
#10	16	0.157	0.149	0.197	0.157
#12	14	0.183	0.173	0.236	0.197
#14	14	0.220	0.210	0.284	0.244

AISI 1016 - 1024 or equivalent steel
All dimensions are in inches.

Washer Dimensions

Dimensional Specifications & Product DetailsNeo-EPDM Washers Used With Self Drilling Screws

Neo-EPDM Washers Used With Self Drilling Screws dimensions

For Use with Screw of this Nominal Diameter	S		N		G	C		E
	Outside Diameter of Steel Section		Inside Diameter of Steel Section		Thickness of Steel Section	Inside Diameter of EPDM Section		Thickness of EPDM Section
	Max	Min	Max	Min	Ref	Max	Min	Max	Min
#8	0.507	0.491	0.212	0.196	0.031	0.149	0.126	0.087	0.070
#10	0.507	0.491	0.212	0.196	0.031	0.149	0.023	0.087	0.070
#12	0.558	0.542	0.243	0.227	0.031	0.197	0.172	0.087	0.070
#14	0.617	0.601	0.275	0.259	0.031	0.232	0.208	0.087	0.070

NOTE: There is no single standard for Neo-EPDM dimensions. These values are offered as a guide; deviations from these specifications may occur.
All dimensions are in inches.

Material	Steel Section of Washer: 20 gauge steel Elastic Section of Washer: Style 40 EPDM sheet
Hardness	EPDM Material: Shore A 65 - 75 (Durometer scale)
Plating	Steel Section of Washer: Galvanized

Hex Head Tek Screw With Washer, Coated

of 1

Sort By

View

Diameter Length Tek Type Item # Availability Price Quantity UOM

#14

7/8

Stitch

DWHC 140087ST

In Stock

$0.22418/EA

See Quantity Discounts

14 X 7/8 HEX HEAD STITCH SCREW WITH WASHER, COATED

$0.22418/EA

Qty

In Stock

Product Detail

Quantity	Price
Quantity	Price
1	$0.22418/ EA
590	$0.21147/ EA
2360	$0.18643/ EA
10590	$0.13132/ EA

#14

DWHC 140100

3-5 Working Days

$0.3222/EA

See Quantity Discounts

14 X 1 HEX HEAD #3 TEK WITH WASHER, COATED

$0.3222/EA

Qty

3-5 Working Days

Product Detail

Quantity	Price
Quantity	Price
1	$0.3222/ EA
500	$0.30392/ EA
2000	$0.26795/ EA
9000	$0.18873/ EA

#14

1 1/4

DWHC 140125

In Stock

$0.29308/EA

See Quantity Discounts

14 X 1 1/4 HEX HEAD #3 TEK WITH WASHER, COATED

$0.29308/EA

Qty

In Stock

Product Detail

Quantity	Price
Quantity	Price
1	$0.29308/ EA
450	$0.27646/ EA
1780	$0.24373/ EA
8000	$0.17167/ EA

#14

1 1/2

DWHC 140150

In Stock

$0.35427/EA

See Quantity Discounts

14 X 1 1/2 HEX HEAD #3 TEK WITH WASHER, COATED

$0.35427/EA

Qty

In Stock

Product Detail

Quantity	Price
Quantity	Price
1	$0.35427/ EA
400	$0.33418/ EA
1590	$0.29462/ EA
7120	$0.20752/ EA

#14

DWHC 140200

In Stock

$0.31657/EA

See Quantity Discounts

14 X 2 HEX HEAD #3 TEK WITH WASHER, COATED

$0.31657/EA

Qty

In Stock

Product Detail

Quantity	Price
Quantity	Price
1	$0.31657/ EA
350	$0.29862/ EA
1400	$0.26327/ EA
6300	$0.18544/ EA

ASME B18.6.3-2013
Nominal Size	A		W	H		F		U
	Width Across Flats		Width Across Corners	Height of Head		Diameter of Washer		Thickness of Washer
	Max	Min	Min	Max	Min	Max	Min	Max	Min
#4	0.188	0.181	0.202	0.060	0.049	0.243	0.225	0.019	0.011
#6	0.250	0.244	0.272	0.093	0.080	0.328	0.302	0.025	0.015
#7	0.250	0.244	0.272	0.093	0.080	0.328	0.302	0.029	0.017
#8	0.250	0.244	0.272	0.110	0.096	0.348	0.322	0.031	0.019
#10	0.312	0.305	0.340	0.120	0.105	0.414	0.384	0.031	0.019
#12	0.312	0.305	0.340	0.155	0.139	0.432	0.398	0.039	0.022
#14	0.375	0.367	0.409	0.190	0.172	0.520	0.480	0.050	0.030

Hex Head Tek Screw With Washer, Coated

Technical Data

Drill Point Specifications

#2 & #3 Standard Drill Point Self Drilling Screws

#4 & #5 Drill Point Self Drilling Screws for Thicker Materials

#1 Drill Point Self Drilling Stitch Screws

Head Dimensions

Dimensional SpecificationsHex & Hex Washer Heads for Self-Tapping & Self-Drilling Screws

Washer Dimensions

Dimensional Specifications & Product DetailsNeo-EPDM Washers Used With Self Drilling Screws

You've Selected

Length

Point Type

Drive Size

14 X 7/8 HEX HEAD STITCH SCREW WITH WASHER, COATED

14 X 1 HEX HEAD #3 TEK WITH WASHER, COATED

14 X 1 1/4 HEX HEAD #3 TEK WITH WASHER, COATED

14 X 1 1/2 HEX HEAD #3 TEK WITH WASHER, COATED

14 X 2 HEX HEAD #3 TEK WITH WASHER, COATED